Nearly everybody may have their private theory involving How to Install a Bathtub.
Setting up a tub isn't specifically brain surgery, yet it does need strong plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably challenging job. If the old tub is conveniently accessible, the task can move speedily; if you need to open a wall to remove the old tub and also place the brand-new tub, the task is much harder. In either situation, the project is within a home handyman's skills, although you will certainly require an assistant to leave the old tub and embeded in the new one. Make certain you have certified on your own for the job and also are comfortable trying it. Instead of working with a specialist to take control of a halfway-completed job, it is better to think about employing one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This post will certainly assist you set up a new bath tub in your washroom if you have actually currently bought a new tub and do not require to alter the setup of your previous supply of water pipes.
Your devices as well as material list ought to comprise the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any kind of water staying in the system. The procedure of removing the existing faucets can be quite bothersome because of the limited access that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the staying water that will certainly come from the pipelines. Once the supply pipes have been removed, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. When the taps have been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
Before proceeding to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end supplies a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in location between the tap and also the sink. Safeguard the tap in position with the producer provided backnut. As soon as the faucet is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The previous type ought to be attached to the tap ends first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Using both wood boards under its feet, position the bath tub in the called for placement. The wood boards are handy in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the tub up until the spirit level checks out degree.
To set up faucets, fit the bottom of the furthest adaptable tap port to the appropriate supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water system and also check all joints and new pipework for leakages and also tighten them if necessary. Fill the bathtub and likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the supplier's user's manual. Tiling and also sealing around the bathtub should wait till the bath tub has actually been used at the very least once as this will resolve it into its last setting.
Getting ready for the Setup
First of all, the sustaining structure supplied with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is essential to ensure that if the faucet includes a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps device to stop strain on the bathtub.
Fit the versatile faucet ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its last setting.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to break a stiff seal, causing the water to penetrate the wall surface in between the bath and also the tiling, resulting in issues with dampness as well as feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to blend in your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to permit the activity experienced when the tub is in use. The sealer can fracture rather early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently readily available on the market. It is suggested to fit the tiles utilizing waterproof or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed reading our article on How to Install a Bathtub Yourself. Thanks a ton for taking time to read our blog. Sharing is nice. You just don't know, you may just be helping someone out. Thanks for going through it.
We're your solution!